Homemade EMF Protection For A Solar Power Bank

*This post may include affiliate links, which allow me to make a small commission off your purchases. The money is earned at no additional cost to you.

In this blog article, you will learn how to create homemade EMF protection for your solar power bank or for other devices. Originally, I made the EMP bag with a zipper. But after 4 years of use, I found the zipper didn’t hold up very well. Hence, I have converted the bag to a roll top. I’ve included directions for the original bag along with information on how to create the roll top. Between this blog article and an accompanying YouTube videos, you should be able to find enough information to get started.

Zipper Bag Measurements….

Bluetti measures 16.5″ long x 11″wide x 16″ high. Once you have measurements, round half numbers up. So, 16.5 rounds up to 17. Once you’ve rounded up the numbers, use the formula width + length + 2. In the case of this Bluetti, 17+11+2 = 30. This means, I need to cut a 30″x30″piece of fabric on the fold for your zipper bag. But, your number will depend on your own individual measurements.

With fabric still folded, there is another cut to make for the base. To get measurements, add width+length+height. Then, take the square root of that number. In my case, 17+11=16= 44. The square root of 44 is 6.63. Round the number down this time. I rounded down to get 6. To create the base, I simply cut out a 6×6 square on each side of the folded fabric. The removed fabric left me with 18 inches of width for the 17 inch Bluetti base. For the roll top variation, see below.

The black squares on far left and right represent the 6″x6″ squares cut away from the fold.

Please, do apply the same measurement method to your solar power bank or any other kind of faraday bag make because it will reduce confusion and headaches. Most importantly, consider how the bag will open and close. For myself, I decided to use a zipper for the bag opening. The zipper required me to use extra fabric to create a lapped zipper for extra EMF protection.

Roll Top Version

Bluetti measures 16.5″ long x 11″wide x 16″ high. Once you have measurements, round half numbers up. So, 16.5 rounds up to 17. Once you’ve rounded up the numbers, use the formula width + length + 2. In the case of this Bluetti, 17+11+2 = 30. Since we are making a roll top bag, you will need to cut your fabric on the fold 30″ wide and 30″ tall + however long you would like the roll top to be. In my case, I made the roll 16 inches tall. Therefore, this would require a piece of fabric cut on the fold at 30″wide + 46″ tall.

With fabric still folded, there is another cut to make for the base. To get measurements, add width+length+height. Then, take the square root of that number. In my case, 17+11=16= 44. The square root of 44 is 6.63. Round the number down this time. I rounded down to get 6. To create the base, I simply cut out a 6×6 square on each side of the folded fabric. The removed fabric left me with 18 inches of width for the 17 inch Bluetti base.

All the supplies for the bag..

For the Bluetti solar power bank EMF bag, I used:

Wax the canvas

Add Parafin and Bee’s Wax to a crock pot. Turn the crock pot on high. Then, wait for the mixture to melt. After the mixture is melted, fold the fabric in half and brush the mixture on. Make sure ever piece of the fabric is soaked. Then, use an iron to ensure the wax has fully soaked into the fabric.

Allow the fabric rest until it is fully dry. Now, you are ready to sew up your homemade EMF bag.

Get updates on the latest posts straight to your inbox 🙂

How to sew up the homemade EMF protection

To create this homemade EMF protection, start by laying the EMF fabric down. Then, lay the canvas fabric on top with the right side facing upwards toward you. Now, place the YKK zipper down with the right side facing the right side of your canvas fabric. Pin in place. Sew and top sew.



Now, fold up the Nylon webbing 1 inch on each side. Place the folded webbing onto the bottom of your bag and pin it into place. Now, sew the webbing down and secure it with a barn door stitch on the bottom and top. Note: I usually place the barn doors 2 inches below the top of the bag and two inches above the bottom.

Once your nylon webbing is attached, pin the other side of your zipper to the opposite side of the fabric. Sew the zipper down.

You should see the bag taking shape now! Now, sew the corners of your bag closed.

You are now in the home stretch of making this bag. To finish, place the lining and canvas fabric together with right sides facing. Sew up both sides, leaving a big enough hole in the lining to turn this bag to the inside.

Last, you’ll want to turn the bag right side out and sew the hole in the lining closed.

Roll Top Variation

Male on left. To secure satin stitch the open pieces down. Female end on left. Here, you can clearly see the 3″ of slack between the bag and buckle.

Align the nylon webbing round the top your bag. The loose ends of the webbing should be on one side. Then, add the female end of the buckle on the non-open side and the male end to the open side (see illustration). Leave 3inches of slack between the bag and the buckles at each end. Pin in place. Then, sew the webbing with 1/2 seam across the top and sew again at the bottom of the webbing as well with 1/2 seam. To close the open side of your webbing on the female buckle end. Do a satin stitch.

Originally posted June 2022  & Last Updated November 2026

Other Helpful Articles

One Quick Tip on How To Sew Grow Bags For Your Garden

How to Upholster A Microsoft Sculpt Mechanical Keyboard

No Comments

Leave a response